Page 1 of 1

Ukulele (or guitar) Scarf Joints

Posted: Sat Apr 04, 2020 3:04 pm
by Bob Gleason
First of all, thanks to Charlie and the MIMF for adding an ukulele section to the board index. Worth a try. Hopefully we'll get interest.I make a few guitars, but mostly ukes. These days I have the time to improve some of my jigs. Here is one I re-made in the last few days for cutting headstock scarf joints. I have a 12" chop saw, but I think a 10" would work. The 2 x 4 is screwed and glued at 90 degrees to the normal 90 degree cut position of the blade. The clamps are left over from some project I never finished. Available on Amazon. By flipping the jig around and swinging the blade to the desired degrees, I can cut 14 degree flat heads or 8 degree slot heads. Often still takes a couple of passes with a sharp handplane, but the cut is very close. A sharp blade is important. If you have a sliding chop saw like mine, don't forget to set the stop so that the carriage can't grab and jump out.
DSC_0025.jpeg

Re: Ukulele (or guitar) Scarf Joints

Posted: Tue Apr 07, 2020 7:51 pm
by Tom Snape
I cut scarf joints on my bandsaw using a sled that rides in the slot in the table. The first version was just a chunk of angle iron fastened to a piece of keystock. I had holes set up for 12° and 15°. The problem was that the legs of the angle were not exactly square to each other, so I ended up having to shim the blank. You can see the light colored shim at the top of the blank in the photo. Also it was possible to rock the sled a little, making a less than perfect cut.

I made another sled from good quality plywood, and made sure that the fence that the blank clamps to is square to the base. This works well. It also has a piece of keystock fastened to the bottom that is good fit to the slot in the table. I only cut 15° scarf joints with this one. A little clean up with a plane and it's ready for glue.
Scarf_Jig_01.jpg
Scarf_Jig_02.jpg

Re: Ukulele (or guitar) Scarf Joints

Posted: Wed Apr 08, 2020 9:56 pm
by Carl Dickinson
Here's a quick, simple way to cut the joint that I've used on the last couple of guitar necks I've made. Clamps hold the neck blank to the fence and taper jig. I used an 80 tooth blade. The blade is lowered all the way to set up the cut, then crank it up into the neck blank. Tweak the blade angle until you get an absolute 90 degrees on the blank (or scrap). After a clean cut, I've needed no adjustment before gluing.
IMG_20200408_153952_3.jpg
IMG_20200408_154230_4.jpg
IMG_20200408_154306_8.jpg
IMG_20200408_155359_2.jpg

Re: Ukulele (or guitar) Scarf Joints

Posted: Fri May 08, 2020 1:02 am
by Paul Montgomery
I've had different jigs and methods to do scarph joints. My latest does so much more. It wasn't hard to make, didn't take long, makes me wonder why I didn't do it sooner.

https://youtu.be/cVPjIvQGOt4

Re: Ukulele (or guitar) Scarf Joints

Posted: Fri May 14, 2021 12:03 pm
by Tyra Noah
The way you do it makes it seem so simple.
I will try and follow along with your instructions.
Thanks. :D :D

Re: Ukulele (or guitar) Scarf Joints

Posted: Mon May 17, 2021 10:11 am
by Ed Minch
I enjoy hand tools, and the neck scarf joint is one of the most fun jobs - especially on a uke which only takes a minute or two

https://www.flickr.com/photos/ruby1638/ ... 488198220/


Ed M

Re: Ukulele (or guitar) Scarf Joints

Posted: Wed Aug 25, 2021 2:21 pm
by Matthew Lau
Hey Paul,

Just saying thanks for sharing that.

I may have to make one also.

-Matt

Re: Ukulele (or guitar) Scarf Joints

Posted: Sun Apr 03, 2022 8:06 am
by Jo Dusepo
I had a similar jig for cutting scarf joints on my table saw, but I usually prefer to cut them by hand with a dozuki saw these days. This enables me to adjust the desired angle for the various instruments I built and their different types of headstocks.